RACKWARE®:  19" EIA Panels

Blank:



AFP: alum. panel

Aluminum flat panel (0.125"). Black wrinkle powder epoxy finish. specs

AP: alum. panel

Aluminum panel, flanged (16-ga.). Black wrinkle powder epoxy finish. specs

SP: steel panel

Steel panel, flanged (16-ga.). Black wrinkle powder epoxy finish. specs

SEP: steel panel

Steel economy panel, flanged (18-ga.). Black smooth semi-gloss finish. specs

SEFP: steel panel

Steel economy flat panel (14-ga.). Black smooth semi-gloss finish. specs

Vented:

SVP: vent panel

Steel vented panel, flanged (18-ga.). Black smooth semi-gloss finish. specs

SVSP: slotted panel

Steel vented slotted panel, flanged (18-ga.). Black smooth semi-gloss finish. specs

Cutouts:

D4P-1: panel

1U panel with 4 Decora-style cutouts mounts system devices, controls and connectors in minimal rack space. Mounts low voltage devices with a maximum width of 1.75” (horizontal orientation). Includes kep-nut hardware. Black. specs

SG6P-3: panel

3U panel with cutouts and clips. Front load up to 6 single-gang (standard wallplate) devices that install with 2 screws. Panel was engineered to rackmount single-gang devices that have a non-removable front plate. Note: spacing is not suitable for 2-gang devices. Black. specs

Cutouts
with ID (label):

D3P-ID-1: panel

1U flanged steel panel with 3 Decora-style cutouts mounts low voltage devices with a maximum width of 1.75 inches (horizontal orientation). Includes Pocket-ID® label holder at the left of each cutout, and kep-nut hardware. Black. Does not include controls. specs  

Template for label:  POCKETID-E

D3P-ID-2: panel

2U flanged steel panel with 3 Decora-style cutouts, accommodates up to 3 wide-body attenuators (Lowell model 200LVC or 150LVCS) mounted in horizontal openings. Includes Pocket-ID® label holder at the left of each cutout, and kep-nut hardware. Black. Does not include controls. specs

Template for label:  POCKETID-E

D8P-ID-3: panel

3U flanged steel panel mounts 8 single-gang Decora-style devices. Includes Pocket-ID® label holder above cutouts, and kep-nut hardware. Note: order blank filler plates (model no. DBB-4) to fill unused cutout positions. specs

Template for label:  POCKETID-A

D9P-ID-3: panel

3U flanged steel panel mounts 9 single-gang Decora-style devices or 4 multi-gang devices using alternate spaces (i.e. Lowell model no. 200LVC or 150LVCS fit in every other space. Clearance for non-Lowell controls should be confirmed). Includes Pocket-ID® label holder above cutouts, and kep-nut hardware (order blank filler plates to fill unused positions separately). specs

Template for label:  POCKETID-B

DBB-4: panel

Decora-style blank filler plate, black finish (4-pack).

IP-ID-1: panel

Identification panel with Pocket-ID® – IU flanged steel panel with label area to identify equipment installed above and below panel position. specs

Template for label:  POCKETID-D

N10P-ID-1:

1U flanged steel panel mounts up to 10 Neutrik D-series connectors or Switchcraft E-series (not included). Black and nickel-plated screws (24 ea.) included for connector installation. Note: blank filler plates for this panel can be ordered directly from Neutrik (#DBA). specs

Template for label:  POCKETID-C

LVC8P-ID-2: panel

2U flanged steel panel mounts up to 8 Lowell LVC-RM-series volume controls (sold separately). Includes filler plugs for unused positions. Device hardware not included with panel. specs

Template for label:  POCKETID-A

Note: this panel can also be ordered pre-loaded with up to 8 volume controls. See spec sheet for details.