products

Stand-Alone Racks

USA FlagStandalone racks are often used for installations where only a few racks are required or where multiple racks are positioned in different locations. Made in the USA.

LBR Series: Standalone Rack

Specs   |   CAD Drawings   |   Photos   |   Accessories

The LBR Series standalone rack with welded side panels and fixed-position front mounting rails is the economical choice for applications that will not need equipment to be set deeper into the rack. Fully welded 18-gauge steel with 16-ga. base is reinforced at all load-bearing junctions. Black wrinkle powder epoxy finish. Made in the USA. with certified U.S. steel. UL2416 Listed

share

LER Series: Enclosed Rack

Specs   |   CAD Drawings   |   Photos   |   Accessories

The LER Series standalone floor rack features welded side panels for security and protection. Fully welded 16-ga. steel rack with 14-ga. base is reinforced at all load-bearing junctions. Adjustable mounting rails, tapped 10-32. Beveled front/rear corners. Black wrinkle powder epoxy finish. Made in the USA. 18-44 rack units. UL2416 Listed

share

LER with accessory bundle

Specs   |   Photos

The LER---BAV is a standard LER Series rack that ships with a bundle of accessories, which are not installed but packaged separately. The rack is 27 in. D – 24.24 in. usable x 23.06 in. W [686 mm deep – 616 mm usable x 586 mm wide]. It’s welded 16-ga. steel with 14-ga. steel bottom and reinforced at load-bearing junctures. Rack is UL2416 Listed

share

LER with installed accessories

Specs   |   Photos

Another time-saving option is to order the LER rack with a set of pre-installed accessories (quantities and style vary with rack height). Rack models with the "IAV" suffix include side panels and rear door as well as other installed accessories. Rack is UL2416 Listed.

share

LHR Series: Host Rack

Specs   |   CAD Drawings   |   Photos   |   Videos   |   Accessories

A two-part rack engineered for quick access to equipment connections even when set against a wall or in back-to-back configurations, the LHR features an exterior cabinet and an interior rack that slides out and rotates. Made in the USA.

share

LLR Series: Laminated Rack

Specs   |   CAD Drawings   |   Photos   |   Accessories

The LLR is a wood composite rack with a premium “Cathedral Black” wood-grain laminate finish, especially suited to home offices or entertainment areas. Front mounting rails, tapped 10-32. Made in the USA. Ships unassembled. 10-21 rack units. 

share

LRR Series: Relay Rack

Specs   |   CAD Drawings   |   Photos   |   Accessories

The LRR Series relay rack provides full access to electronics for telecommunications, commercial sound, broadcast, data, and switching applications. The vertical channels are 11-gauge steel with integral rails tapped 10-32 on E.I.A. mounting centers. Base and top angle supports are two-piece aluminum construction. Made in the USA. Ships unassembled. 38 and 45 rack units.

share

LSER Series: Seismic Enclosed Rack

Specs   |   CAD Drawings   |   Photos   |   Accessories

The LSER code compliant, seismic-certified rack is P.E. certified to meet or exceed the seismic design requirements as specified in the 2009 International Building Code (IBC), Section 1613; the 2007 California Building Code (CBC), Section 1613; and California's Office of Statewide Health Planning and Development (OSHPD). Downloadable documentation is also shipped with each rack. Adjustable mounting rails, tapped 10-32, include printed RU scale to facilitate gear-mounting. Black wrinkle powder epoxy finish. Made in the USA with certified U.S. steel. 35-44 rack units. UL2416 Listed

share